Introduction

USB 3.0 is the second major revision of the Universal Serial Bus (USB) standard for computer connectivity. USB 3.0 implements a 5.0 Gbit/s raw transfer rate using 8b/10b encoding. USB 2.0 implements the Hi-Speed mode (HS – 480 Mbit/s), while USB 1.1 implements Low Speed (LS) – 1.5 Mbit/s and Full Speed (FS) – 12 Mbit/s). The USB 3.0 Controller used shall provide one 5.0Gbit/s USB channel using the PS internal GT as PHY.

Table of Contents

HW/IP Features

The ZynqMP USB 3.0 Controller shall provide one 5.0Gbit/s USB channel using the PS internal GT as PHY.
Two USB 2.0/3.0 controllers
Compliant with USB 3.0 specs
Compliant with xHCI standard
Supports 5.0 Gbps data rate
Support host, device and OTG modes
Support On The Go (OTG) 2.0 host/device selection
Provide simultaneous operation of the USB2.0 and USB3.0 interfaces where applicable
In host mode, as required by the standard for speed negotiation and switching
In device mode, statically configured as USB2.0 or USB3.0
In OTG mode, dynamically switch between host role and device role
HNP, SRP supported at USB 2.0 speeds in OTG
DRD supported in USB 3.0 speeds
64-bit AXI master port with built-in DMA
Register programming via AXI and/or APB slave ports
Power management features: hibernation mode
Support 44-bit address space
Supports Link Power Management (LPM) transfers to save power when bus is idle

Features supported in driver
All the HW/IP features are supported by driver
Missing Features, Known Issues and Limitations
ZynqMP USB 3.0 controller doesn't support USB 3.0 OTG (On The Go) host/device selection

Important AR links

USB core reset in Linux can cause issues with USB device connected if it was previously powered in U-boot - AR-72376
USB3.0 device mode does not work when booting through USB boot mode - AR-72409
USB 3.0 standalone device driver does not send STALL response for every unsupported command - AR-71925
USB 3.0 port hangs after plug-in and plug-out cable in gadget mode - AR-76696
USB DWC3-core getting the clock error message "Failed to get clk 'ref': -2“ - AR-72764
USB Remote wake-up feature support (2020 release) - AR-76750
USB Remote wake-up feature support (2021.1 and later release) - AR-76949

Host Mode

ZCU102 board jumper settings for Host mode
J7 - ON
J113 - 1-2
J110 - 2-3

Please refer the below image for jumper settings on ZCU102 board

USB 3.0 Host mode setup snapshot

Kernel Configuration

Device Drivers------> USB support <*> xHCI HCD (USB 3.0) support <*> USB Mass Storage support <*> DesignWare USB3 DRD Core Support DWC3 Mode Selection (Dual Role mode) ---> (X) Dual Role mode

By enabling the above we need to see the below mentioned Kconfig parameter enabled
CONFIG_USB_DWC3 = y
CONFIG_USB_DWC3_DUAL_ROLE = y
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_PLATFORM=y

Devicetree

usb0: usb0@ff9d0000 { #address-cells = <2>; #size-cells = <2>; status = "disabled"; compatible = "xlnx,zynqmp-dwc3"; reg = <0x0 0xff9d0000 0x0 0x100>; clock-names = "bus_clk", "ref_clk"; power-domains = <&zynqmp_firmware PD_USB_0>; ranges; nvmem-cells = <&soc_revision>; nvmem-cell-names = "soc_revision"; dwc3_0: dwc3@fe200000 { compatible = "snps,dwc3"; status = "disabled"; reg = <0x0 0xfe200000 0x0 0x40000>; interrupt-parent = <&gic>; interrupt-names = "dwc_usb3", "otg", "hiber"; interrupts = <0 65 4>, <0 69 4>, <0 75 4>; #stream-id-cells = <1>; iommus = <&smmu 0x860>; snps,quirk-frame-length-adjustment = <0x20>; snps,refclk_fladj; snps,enable_guctl1_resume_quirk; snps,enable_guctl1_ipd_quirk; snps,xhci-stream-quirk; /* dma-coherent; */ /* snps,enable-hibernation; */ }; }; &usb0 { status = "okay"; }; &dwc3_0 { status = "okay"; dr_mode = "host"; };

Test Procedure
Connect the USB 3.0/2.0 pendrive to USB 3.0 capable board and see it getting detected in /dev/sd<x>.
Expected Output
Once Linux boots the below highlighted prints should be visible when we connected the mass storage device

84943.023896] usb 2-1: new SuperSpeed USB device number 4 using xhci-hcd [84943.044949] usb 2-1: New USB device found, idVendor=0781, idProduct=5581 [84943.051579] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [84943.058695] usb 2-1: Product: SanDisk Ultra [84943.062858] usb 2-1: Manufacturer: SanDisk [84943.066939] usb 2-1: SerialNumber: A20037A3AD063355 [84943.072653] usb-storage 2-1:1.0: USB Mass Storage device detected [84943.078836] scsi host1: usb-storage 2-1:1.0 [84944.080804] scsi 1:0:0:0: Direct-Access SanDisk SanDisk Ultra PMAP PQ: 0 ANSI: 6 [84944.089531] sd 1:0:0:0: [sda] 30283008 512-byte logical blocks: (15.5 GB/14.4 GiB) [84944.097708] sd 1:0:0:0: [sda] Write Protect is off [84944.103904] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [84944.309725] sda: [84944.312888] sd 1:0:0:0: [sda] Attached SCSI removable disk

Performance
When Mass Storage device is connected
Device used :
USB 3.0 : HP USB 3.0 16 GB pendrive (idVendor=03f0, idProduct=4840)
USB 3.0 - UASP capable drive - Transcend Storjet 128GB
USB 2.0 : Sandisk Cruzer Blade USB 2.0 8 GB Pendrive (idVendor=0781, idProduct=5567)

Using HDPARM tool
Mode Speed
USB 3.0 (Super Speed) 128 MB/sec
USB 3.0 (UASP capable) 327.10 MB/sec
USB 2.0 (High Speed) 25.48 MB/sec

Note : Above results may vary from device to device

When Ethernet device is connected
Device used :
USB 3.0/2.0 : Xilinx ZynqMP RNDIS/Ethernet Gadget

Using Iperf tool (TCP)
Mode Speed
USB 3.0 (Super Speed) 761.6 Mbits/sec
USB 2.0 (High Speed) 467.2 Mbits/sec

Using Iperf tool (UDP)
Mode Speed
USB 3.0 (Super Speed) 761.6 Mbits/sec
USB 2.0 (High Speed) 467.2 Mbits/sec

Note : The above results are taken with LPM mode disabled

Peripheral Mode
ZCU102 jumper settings for Peripheral mode
J7 - OFF
J113 - 1-2
J110 - 1-2
J109- No jumper

Please refer the below image for jumper settings required for peripheral mode on ZCU102 board

USB 3.0 peripheral mode setup snapshot

This document only explains the USB 3.0 peripheral mode configurations for MASS STORAGE gadget or ETHERNET Gadget profiles.
Mass Storage
Kernel Configuration

Device Drivers--------> USB support <*> USB Gadget Support <M> USB Gadget Drivers <M> Gadget Filesystem <M> Mass Storage Gadget File systems ---> Pseudo filesystems ---> {M} Userspace-driven configuration filesystem

By enabling the above we need to see the below mentioned Kconfig parameter enabled
CONFIG_USB_DWC3 = y
CONFIG_USB_DWC3_DUAL_ROLE = y
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_PLATFORM=y

CONFIG_CONFIGFS_FS=m
CONFIG_USB_GADGET=y
CONFIG_USB_LIBCOMPOSITE=m
CONFIG_USB_F_MASS_STORAGE=m
CONFIG_USB_CONFIGFS=m
CONFIG_USB_CONFIGFS_MASS_STORAGE=y

Please find the required .ko files in the below mentioned paths:

linux-xlnx/fs/configfs/configfs.ko
linux-xlnx/drivers/usb/gadget/libcomposite.ko
linux-xlnx/drivers/usb/gadget/legacy/gadgetfs.ko
linux-xlnx/drivers/usb/gadget/function/usb_f_mass_storage.ko
linux-xlnx/drivers/usb/gadget/legacy/g_mass_storage.ko

Devicetree

usb0: usb0@ff9d0000 { #address-cells = <2>; #size-cells = <2>; status = "disabled"; compatible = "xlnx,zynqmp-dwc3"; reg = <0x0 0xff9d0000 0x0 0x100>; clock-names = "bus_clk", "ref_clk"; power-domains = <&zynqmp_firmware PD_USB_0>; ranges; nvmem-cells = <&soc_revision>; nvmem-cell-names = "soc_revision"; dwc3_0: dwc3@fe200000 { compatible = "snps,dwc3"; status = "disabled"; reg = <0x0 0xfe200000 0x0 0x40000>; interrupt-parent = <&gic>; interrupt-names = "dwc_usb3", "otg", "hiber"; interrupts = <0 65 4>, <0 69 4>, <0 75 4>; #stream-id-cells = <1>; iommus = <&smmu 0x860>; snps,quirk-frame-length-adjustment = <0x20>; snps,refclk_fladj; snps,enable_guctl1_resume_quirk; snps,enable_guctl1_ipd_quirk; snps,xhci-stream-quirk; /* dma-coherent; */ /* snps,enable-hibernation; */ }; }; &usb0 { status = "okay"; }; &dwc3_0 { status = "okay"; dr_mode = "peripheral"; };

Performance
Using HDPARM tool (Linux Host)
Link Power Management (LPM) mode Enable
Mode Speed
USB 3.0 (Super Speed) 127.18 MB/sec
USB 2.0 (High Speed) 38.82 MB/sec

Link Power Management (LPM) mode Disable
Mode Speed
USB 3.0 (Super Speed) 237 MB/sec
USB 2.0 (High Speed) 38.47 MB/sec
Testing Procedure
Please use the below settings for configuring USB as MASS STORAGE profile in device mode:

insmod configfs.ko insmod libcomposite.ko insmod usb_f_mass_storage.ko insmod gadgetfs.ko dd if=/dev/zero of=/tmp/mydev count=256 bs=1M insmod g_mass_storage.ko file=/tmp/mydev removable=1 stall=1 iSerialNumber=7ABC7ABC7ABC7ABC7ABC7ABC

Testing the mass storage functionality by connecting the board to host using the below steps:
Connect the cable from board to windows host machine
Format the mass storage device that got detected in windows
The windows screen shot when we the device gets detected should be as below
The board will be detected as mass storage drive with size 256 MB.
Copy some files into the mass storage drive , remove the cable and connect it again. We should be able to see the files that we copied into the drive.
Ethernet Gadget
Kernel Configuration
For the xilinx-v2016.2 and prior tags, apply the following patch.

USB support-----> <*> USB Gadget Support <M> USB Gadget Drivers <M> Gadget Filesystem <M> Ethernet Gadget (with CDC Ethernet support) [*] RNDIS support File systems ---> Pseudo filesystems ---> {M} Userspace-driven configuration filesystem

By enabling the above we need to see the below mentioned Kconfig paramter enabled
CONFIG_USB_DWC3 = y
CONFIG_USB_DWC3_DUAL_ROLE = y
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_PLATFORM=y

CONFIG_CONFIGFS_FS=m
CONFIG_USB_GADGET=y
CONFIG_USB_LIBCOMPOSITE=m
CONFIG_USB_ETH=m
CONFIG_USB_ETH_RNDIS=y

Please find the required .ko files in the below mentioned paths:
linux-xlnx/fs/configfs/configfs.ko
linux-xlnx/drivers/usb/gadget/libcomposite.ko
linux-xlnx/drivers/usb/gadget/legacy/gadgetfs.ko
linux-xlnx/drivers/usb/gadget/function/u_ether.ko
linux-xlnx/drivers/usb/gadget/function/usb_f_rndis.ko

Devicetree

usb0: usb0@ff9d0000 { #address-cells = <2>; #size-cells = <2>; status = "disabled"; compatible = "xlnx,zynqmp-dwc3"; reg = <0x0 0xff9d0000 0x0 0x100>; clock-names = "bus_clk", "ref_clk"; power-domains = <&zynqmp_firmware PD_USB_0>; ranges; nvmem-cells = <&soc_revision>; nvmem-cell-names = "soc_revision"; dwc3_0: dwc3@fe200000 { compatible = "snps,dwc3"; status = "disabled"; reg = <0x0 0xfe200000 0x0 0x40000>; interrupt-parent = <&gic>; interrupt-names = "dwc_usb3", "otg", "hiber"; interrupts = <0 65 4>, <0 69 4>, <0 75 4>; #stream-id-cells = <1>; iommus = <&smmu 0x860>; snps,quirk-frame-length-adjustment = <0x20>; snps,refclk_fladj; snps,enable_guctl1_resume_quirk; snps,enable_guctl1_ipd_quirk; snps,xhci-stream-quirk; /* dma-coherent; */ /* snps,enable-hibernation; */ }; }; &usb0 { status = "okay"; }; &dwc3_0 { status = "okay"; dr_mode = "peripheral"; };

Performance
Iperf tool (TCP)
Mode Speed
USB 3.0 (Super Speed) 761.6 Mbits/sec
USB 2.0 (High Speed) 467.2 Mbits/sec

Iperf tool (UDP)
Mode Speed
USB 3.0 (Super Speed) 761.6 Mbits/sec
USB 2.0 (High Speed) 467.2 Mbits/sec
Testing Procedure
Please use the below settings for configuring USB as ETHERNET gadget profile in device mode:

insmod configfs.ko insmod libcomposite.ko insmod u_ether.ko insmod usb_f_rndis.ko mount -t configfs none /sys/kernel/config cd /sys/kernel/config/usb_gadget mkdir g1 cd g1 echo "64" > bMaxPacketSize0 echo "0x200" > bcdUSB echo "0x100" > bcdDevice echo "0x03FD" > idVendor echo "0x0502" > idProduct mkdir configs/c1.1 mkdir functions/rndis.rn0 ln -s functions/rndis.rn0/ configs/c1.1/ echo "fe200000.dwc3" > UDC ifconfig usb0 10.10.70.1 ifconfig usb0 up

Testing the ethernet gadget by connecting to linux/windows machine:
Connect the cable from board to windows/linux host machine
Set the ipaddress on device side
systest# ifconfig usb0 192.168.1.200
Set the ipaddress on host side
ping host address from device side and the result should be ass below mentioned
ping <host address>
Expected Output:

USB Attached SCSI Protocol(UASP)
Limitation
TCM MODULE USED FOR UASP does not support ATA_12 commands. so user needs to change VID and PID in file drivers/usb/gadget/legacy/tcm_usb_gadget.c as below
#define UAS_VENDOR_ID 0x0bc2
#define UAS_PRODUCT_ID 0xa013
Kernel Configuration

Device Drivers ---> <*> Generic Target Core Mod (TCM) and ConfigFS Infrastructure ---> --- Generic Target Core Mod (TCM) and ConfigFS Infrastructure <*> TCM/IBLOCK Subsystem Plugin for Linux/BLOCK <*> TCM/FILEIO Subsystem Plugin for Linux/VFS <*> TCM/pSCSI Subsystem Plugin for Linux/SCSI <*> TCM/USER Subsystem Plugin for Linux <*> TCM Virtual SAS target and Linux/SCSI LDD fabric loopback module <*> Linux-iSCSI.org iSCSI Target Mode Stack [*] USB support ---> <*> USB Gadget Support <*> USB functions configurable through configfs [*] USB Gadget Target Fabric <M> USB Gadget Target Fabric Module

KCONFIG options for UASP profile
CONFIG_USB_DWC3 = y
CONFIG_USB_DWC3_DUAL_ROLE = y
CONFIG_USB_SUPPORT=y
CONFIG_USB_COMMON=y
CONFIG_USB_ARCH_HAS_HCD=y
CONFIG_USB=y
CONFIG_USB_XHCI_HCD=y
CONFIG_USB_XHCI_PLATFORM=y

CONFIG_CONFIGFS_FS=m
CONFIG_USB_GADGET=y
CONFIG_USB_LIBCOMPOSITE=m
CONFIG_USB_CONFIGFS=m
CONFIG_BLK_DEV_INTEGRITY=y
CONFIG_TARGET_CORE=y
CONFIG_TCM_IBLOCK=y
CONFIG_TCM_FILEIO=y
CONFIG_TCM_PSCSI=y
CONFIG_TCM_USER2=y
CONFIG_LOOPBACK_TARGET=y
CONFIG_ISCSI_TARGET=y
CONFIG_USB_F_TCM=y
CONFIG_USB_CONFIGFS_F_TCM=y
CONFIG_USB_GADGET_TARGET=m
CONFIG_CRC_T10DIF=y

Devicetree
Example Device tree node:

&dwc3_0 { status = "okay"; dr_mode = "peripheral"; }

Please find the required .ko files in the below mentioned paths:
linux-xlnx/fs/configfs/configfs.ko
linux-xlnx/drivers/usb/gadget/libcomposite.ko
linux-xlnx/drivers/usb/gadget/legacy/gadgetfs.ko
linux-xlnx/drivers/usb/gadget/legacy/tcm_usb_gadget.ko

Performance
HDPARM Tool (UBUNTU Host)
Link Power Management (LPM) mode Result
Enabled 367.77 MB/sec
Disabled 381.42 MB/sec
Test procedure
Connect the USB 3.0 cable to linux PC and perform the steps given below on the device side

Install module

modprobe tcm_usb_gadget

Mount the configfs

mount a -t configfs /sys/kernel/config

Create a memory that will be assigned to gadget (here creating memory of 750MB)

mkdir /root dd if=/dev/zero of=/root/file.bin bs=10M count=75

Format the memory that just has been created

mkdosfs -v /root/file.bin -n ramfs

Assign memory to gadget module

mkdir -p /sys/kernel/config/target/core/fileio_0/fileio echo "fd_dev_name=/root/file.bin,fd_dev_size=734003200" > /sys/kernel/config/target/core/fileio_0/fileio/control echo 1 > /sys/kernel/config/target/core/fileio_0/fileio/enable mkdir -p /sys/kernel/config/target/usb_gadget/naa.6001405c3214b06a/tpgt_1 mkdir /sys/kernel/config/target/usb_gadget/naa.6001405c3214b06a/tpgt_1/lun/lun_0 echo naa.6001405c3214b06a > /sys/kernel/config/target/usb_gadget/naa.6001405c3214b06a/tpgt_1/nexus ln -s /sys/kernel/config/target/core/fileio_0/fileio /sys/kernel/config/target/usb_gadget/naa.6001405c3214b06a/tpgt_1/lun/lun_0/virtual_scsi_port

Change max busrt to get maximum performance

echo 15 > /sys/kernel/config/target/usb_gadget/naa.6001405c3214b06a/tpgt_1/maxburst

Connect device to Host

echo 1 > /sys/kernel/config/target/usb_gadget/naa.6001405c3214b06a/tpgt_1/enable

Ubuntu
On performing the steps given above, below prints should be shown on host side on typing "dmesg"

Do data transfer on HOST(UBUNTU) side

Windows
Note: UASP is supported from windows 8

On windows need to follow below steps in order to mount device

1. open manage by right click on Desktop (screen shot as below)

2. open disk management and format the device (screen shot as below)

3. It will mount the device as drive
4. Do data transfer

OTG Mode
Using the correct cables is the key to OTG operation. Testing was done using two cables joined together to create an OTG cable. An OTG cable has a micro A connector on one end and a micro B connector on the other end. The micro A connector is the host side of the cable and the micro B connector is the device side by default.

Hardware Setup
Boards: ZynqMP ZCU102 (2 boards back to back connected)
Host Machine: Linux Machine with USB 3.0 ports
Kernel Configuration
Linux Kernel image with xHCI Host enabled (static) and Mass Storage Gadget created as dynamic module
Boot image for initial FSBL sequence
Device tree with DWC USB OTG mode enabled
Steps to enable OTG in Linux Kernel (add below configurations via menuconfig)
CONFIG_PM=y
CONFIG_USB_OTG=y
CONFIG_USB_OTG_FSM=y
CONFIG_USB_DWC3_OTG=y
After this compile the kernel, install modules in it and create kernel Image.
Test Procedure
When the Linux kernel boots up, give the below commands:
$ dd if=/dev/zero of=/tmp/mydev count=256 bs=1M
$ modprobe g_mass_storage file=/tmp/mydev removable=1 stall=1 iSerialNumber=7ABC7ABC7ABC7ABC7ABC7ABC

Peripheral Mode
Connect board to any Host PC via USB Std-A-Male to Micro-B-Male cable.
It should be detected as a Mass Storage Device
Do some data transfers

Host Mode
Connect any pen-drive with the board via USB Micro-A-Male to Std-A-Female type connector
Check that the pen-drive is detected properly
Do some data transfers.

HNP & SRP
When two boards (OTG enabled) are connected back to back, OTG 2.0 supports HNP and SRP
To start HNP from the Device, issue below command
$ echo 1 > /sys/devices/platform/amba/ff9d0000.usb0/fe200000.dwc3/hnp
Please check the role reversal on both the boards
To start SRP from the Device, issue below command
$ echo 1 > /sys/devices/platform/amba/ff9d0000.usb0/fe200000.dwc3/srp

Note : Both Host and Peripheral mode should work without resetting/rebooting the board.

Mainline Status
The current driver available in the Xilinx Linux git is in sync with the open-source kernel driver except for the following:

- USB Hibernation feature,

- USB Remote wakeup feature,

- USB OTG feature,

- Suspend-Resume feature.
Phy Settings
This USB controller on Zynq UltraScale+ MPSoC is connected to High Speed GTR through PIPE3 interface. This phy requires a reference clock to operate with USB 3.0, which can be
configured to anyone among 26MHz, 52 MHz, and 100MHz. On the ZCU102 board, this is factory programmed to 26MHz.

Change log

2024.2

cfcbde2db95a usb: misc: onboard_usb_dev: skip suspend/resume sequence for USB5744 SMBus support
75d7a6531b44 usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support
b49d22537a9e usb: misc: onboard_dev: extend platform data to add power on delay field
e388506a215d usb: misc: onboard_hub: rename to onboard_dev
7767a1b016c8 usb: misc: usb5744: Increase post reset delay
c58b2126242b usb: dwc3: Export symbol dwc3_host_wakeup_register/capable
97865157caab Revert "usb: gadget: webcam: Add support for Full HD and 4K UHD Raw Video Formats"
0e710b2f703b Revert "usb: dwc3: Correct usb dma mask for making SMMU work in device mode"
fcd5289e682d Revert "usb: gadget: uvc_video: unlock before submitting a request to ep"

2024.1

6.6 kernel upgrade
a66247a1aa39 dwc3: core: For ZU+ enable GUCTL1 bit 9 for correcting Inter Packet Delay(IPD)
d21f9d46eaba Revert "dwc3: core: Enable GUCTL1 chicken bit 9 for correcting Inter Packet Delay(IPD)"
e06cd16aaa5e usb: dwc3: define dummy dwc3_gadget_*_hibernation APIs for DWC3_HOST mode
1b9e0fd55158 usb: dwc3: define dummy dwc3_host_wakeup_* APIs for DWC3_GADGET mode
c4c8377c917f usb: dwc3: gadget: switch to 'wakeup' interrupt name for hibernation support
f462b9499016 usb: dwc3: Remove not required version.h header

2023.2

None

2023.1

kernel upgrade to 6.1
Added reset-controller support for versal platform
Added power-domains property support

2022.2

None

2022.1

kernel upgrade to 5.15

2021.2

None

2021.1

Created a new Xilinx DWC3 glue driver for better management of Xilinx specific changes
https://github.com/Xilinx/linux-xlnx/blob/master/drivers/usb/dwc3/dwc3-xilinx.c
Kernel upgrade to 5.10

2020.2

None

2020.1

kernel upgrade to 5.4

2019.2

Add support for disabling U1 and U2 entries
Add support for masking phy reset signal
Add wakeup capability support for versal usb controller
Add D0/D3 entry/exit support for versal

2019.1

Start timer per request instead of per endpoint
Correct the logic for checking TRB full in __dwc3_prepare_one_trb()
Check for IOC/LST bit in both event->status and TRB->ctrl fields
Check MISSED ISOC bit only for ISOC endpoints
Don't kick transfer if LST or SHORT bits are set
make otg driver work along with drd driver
mask host/device soft reset from affecting the phy
Add user event for ending hnp session
Add DRD support for versal
route lpd usb traffic through CCI path for making SMMU work
Fixed BUS Expiries for Iscoronous transfers when using usb video class

Related Links

Xilinx Wiki

Zynq Ultrascale MPSOC Linux USB device driver

Introduction

HW/IP Features

Features supported in driver

Missing Features, Known Issues and Limitations

Important AR links

Host Mode

Kernel Configuration

Devicetree

Test Procedure

Expected Output

Performance

Peripheral Mode

Mass Storage

Kernel Configuration

Devicetree

Performance

Testing Procedure

Ethernet Gadget

Kernel Configuration

Devicetree

Performance

Testing Procedure

Expected Output:

USB Attached SCSI Protocol(UASP)

Kernel Configuration

Devicetree

Performance

Test procedure

OTG Mode

Kernel Configuration

Test Procedure

Mainline Status

Phy Settings

Change log

Mode	Speed
USB 3.0 (Super Speed)	128 MB/sec
USB 3.0 (UASP capable)	327.10 MB/sec
USB 2.0 (High Speed)	25.48 MB/sec

Link Power Management (LPM) mode	Result
Enabled	367.77 MB/sec
Disabled	381.42 MB/sec