In this demo, we will demo how to use the fixed link feature in the macb linux driver on the ZCU102 Rev1.0. To demo this, the GEM2 is routed to the GEM3 via the PL. The iptables utility is used here for testing purposes only and are prepended with Opt.

Build Hardware

Launch Vivado 2017.2, create a new project targeting the ZCU102 board.

Use the Block Automation in IPI, make slight PS changes:

Connect as shown below:

Generate Output Products, Create HDL wrapper, write_bitstream and export to SDK (include bitstream).

Build Linux Image

Here, Petalinux 2017.2 is used. See the link here for more info on the Petalinux commands:

cd project_1/project_1.sdk
petalinux-create --type project --template zynqMP --name fixed_link_test
cd fixed_link_test
petalinux-config --get-hw-description=..
- o Save and Exit
Open the system-user.dts in project-spec/meta-user/recipes-bsp/device-tree/files
and make the changes below:

&gem2 {
        phy-mode = "moca";
        fixed-link {
                speed = <1000>;
                full-duplex;
         };
};
&gem3 {
        phy-mode = "moca";
        fixed-link {
                speed = <1000>;
                full-duplex;
         };
};

petalinux-config -c kernel
- (Opt) Networking Support -> Networking Options -> Network Packet filtering framework (Netfilter) -> Core Netfilter Configuration -> <*> Netfilter connection tracking support
- (Opt) Networking Support -> Networking Options -> Network Packet filtering framework (Netfilter) -> IP: Netfilter Configuration -> <*> IPv4 connection tracking support
- (Opt) Networking Support -> Networking Options -> Network Packet filtering framework (Netfilter) -> IP: Netfilter Configuration -> <*> IPv4 NAT
- (Opt) Networking Support -> Networking Options -> Network Packet filtering framework (Netfilter) -> IP: Netfilter Configuration -> <*> IP tables support
- (Opt) Networking Support -> Networking Options -> Network Packet filtering framework (Netfilter) -> IP: Netfilter Configuration -> <*> iptables NAT support
- (Opt) Networking Support -> Networking Options -> Network Packet filtering framework (Netfilter) -> IP: Netfilter Configuration -> <*> MASQUERADE target support
- (Opt) Networking Support -> Networking Options -> Network Packet filtering framework (Netfilter) -> Core Netfilter Configuration -> {*} ipv4/IPV6 redirect support
- Device Drivers -> Network device support -> PHY Device Support and infrastructure -> <*> Driver for MDIO Bus/PHY emulation with fixed/link PHYs

(Opt) petalinux-config -c rootfs
- Filesystem Packages -> misc -> iptables -> [*] iptables
- Filesystem Packages -> misc -> net-tools -> [*] net-tools
petalinux-build
cd images/linux
petalinux-package --boot --fsbl zynqmp_fsbl.elf --fpga design_1_wrapper.bit --u-boot

Testing on Hardware

Place the following files onto the SD card and boot:

BOOT.BIN
Image.ub
command.sh (opt)

Place the commands below into a commands.sh file:

iptables -t nat -A POSTROUTING -s 10.50.0.1 -d 10.60.1.1 -j SNAT --to-source 10.60.0.1
iptables -t nat -A PREROUTING -d 10.60.0.1 -j DNAT --to-destination 10.50.0.1
iptables -t nat -A POSTROUTING -s 10.50.1.1 -d 10.60.0.1 -j SNAT --to-source 10.60.1.1
iptables -t nat -A PREROUTING -d 10.60.1.1 -j DNAT --to-destination 10.50.1.1
ip route add 10.60.1.1 dev eth0
arp -i eth0 -s 10.60.1.1 00:0a:35:00:22:02
ip route add 10.60.0.1 dev eth1
arp -i eth1 -s 10.60.0.1 00:0a:35:00:22:01

Note: If the file was created on a windows OS, make sure that this is converted to Unix. For example dos2unix

Make sure each MAC address is unique. To verify, do a ipconfig -a

User can set the MAC address with the command below:

ifconfig eth0 down
ifconfig eth0 hw ether 00:0a:35:00:22:01
ifconfig eth0 up
ifconfig eth1 down
ifconfig eth1 hw ether 00:0a:35:00:22:02
ifconfig eth1 up

Since we have the system added in a loop, we can use the NAT to set up the LAN and test. This is optional.

To test follow the tests below:

ifconfig eth0 10.50.0.1/24 netmask 255.0.0.0
ifconfig eth1 10.50.1.1/24 netmask 255.0.0.0
mount /dev/mmcblk0p1 /mnt
source /mnt/commands.sh
- Note: User can manually enter the commands from commands.sh above here too
ping 10.60.1.1
ping 10.60.0.1

Zynq Ultrascale Fixed Link PS Ethernet Demo

Table of Contents

Build Hardware

Build Linux Image

Testing on Hardware