This page gives an overview of the bare-metal driver support for the Xilinx® LogiCORE™ IP Arasan SD 2.0 host controller.
Table of Contents
Table of Contents | ||
---|---|---|
|
Introduction
The SD/SDIO controller communicates with SDIO devices, SD memory cards, and MMC cards with up to four data lines. On the SD interface, one (DAT0) or four (DAT0-DAT3) lines can be used for data transfer. The SDIO interface can be routed through the MIO multiplexer to the MIO pins or through the EMIO to Select IO pin in the PL. The controller can support SD and SDIO applications in a wide range of portable low-power applications such as 802.11 devices, GPS, WiMAX, UWB, and others.The SD/SDIO controller is compatible with the standard SD Host Controller Specification Version 2.0 Part A2 with SDMA (single operation DMA), ADMA1 (4 KB boundary limited DMA), and ADMA2 (ADMA2 allows data of any location and any size to be transferred in a 32-bit system memory-scatter-gather DMA) support. The core also supports up to seven functions in SD1, SD4, but does not support SPI mode. The Zynq-7000 SoC is expected to work with eMMC devices because the protocol is the same as SD, but this has not been extensively verified. Users must be careful to meet all timing requirements as they might or might not comply with eMMC. It does support SD high-speed (SDHS) and SD High Capacity (SDHC) card standards. The user should be familiar with the SD2.0/SDIO 2.0 specifications. The SD/SDIO controller also supports MMC3.31 standard. eMMC flash memories are not primary boot devices for Zynq-7000
family, but can be used as secondary boot devices.
The SD/SDIO controller is accessed by the Arm processor via the AHB bus. The controller also includes a DMA unit with an internal FIFO to meet throughput requirements.
...
Driver Name | Path to Vitis | Path in Github |
---|---|---|
sdps | <Vitis Install Directory>/data/embedded/XilinxProcessorIPLib/drivers/sdps | https://github.com/Xilinx/embeddedsw/tree/master/XilinxProcessorIPLib/drivers/sdps/ |
Info |
---|
Note: To view the sources for a particular release, use the rel-version tag in github. For example, for the 2020.1 release, the proper version of the code is: https://github.com/Xilinx/embeddedsw/tree/xilinx-v2020.1/XilinxProcessorIPLib/drivers/sdps |
...
Examples Path:
https://github.com/Xilinx/embeddedsw/tree/master/XilinxProcessorIPLib/drivers/sdps/examples
Test Name | Example Source | Description |
---|---|---|
SDPS Read and Write example without file system | This examples does basic raw read and write test from SD/eMMC device in Polled mode. | |
Read and Write example with file system (using XILFFS library) | This examples does basic file system read and write test from SD/eMMC device in Polled mode. |
Example Application Usage
SDPS Read and Write example without file system
This examples does basic raw read and write test from SD/eMMC device in Polled mode.
Expected Output
Code Block |
---|
SD Raw Read/ Write Test Successfully ran SD Raw Read/ Write Test |
Read and Write example with file system (using XILFFS library)
This examples does basic file system read and write test from SD/eMMC device in Polled mode.
Expected Output
Code Block |
---|
SD Polled File System Example Test Successfully ran SD Polled File System Example Test |
Example Design Architecture
NA
Performance
SD card : Sandisk Ultra 16GB SDHC card
Zynq:
High speed | 20.54 MB/sec |
Changelog
2023.1
None
2022.2
https://github.com/Xilinx/embeddedsw/blob/xlnx_rel_v2022.2/doc/ChangeLog#L140
...
2018.3
None
2018.2
None
2018.1
None
2017.4
https://github.com/Xilinx/embeddedsw/blob/xilinx-v2017.4/doc/ChangeLog#L18
...
https://github.com/Xilinx/embeddedsw/blob/xilinx-v2017.1/doc/ChangeLog#L326
2016.4
https://github.com/Xilinx/embeddedsw/blob/xilinx-v2016.4/doc/ChangeLog#L44
2016.3
https://github.com/Xilinx/embeddedsw/blob/xilinx-v2016.3/doc/ChangeLog#L178
...