Zynq UltraScale MPSoC 2016.2 Tutorial for design module 3

Abstract

• Boot APU, RPU0, and RPU1 independently
  • RPU1 OS: Bare-metal
• Bare-metal performance monitor application
  • Read PS APM counters to measure DDR throughput and prints to UART1

  • Table of Contents

    Abstract

    Block Diagram

    Component Diagram

    Source Code

    How to build images

    How to Execute

Block Diagram

Component Diagram

<<TODO>>

Source Code

• Create workspace folder

$ mkdir 1_apu_smp_linux

• Checkout the source code for Linux

$ git clone https://gitenterprise.xilinx.com/PAEG/zynqmp_petalinux_bsp.git
This creates a folder “zynqmp_petalinux_bsp” and gets all source files from git repository

• Checkout the source code for PMU FW

$ git clone https://gitenterprise.xilinx.com/PAEG/pmu_fw.git
This creates a folder “pmu_fw” and gets all source files from git repository

How to build images

Apply Patches


Apply the design-1 patch (refer DESIGN-1)

$ git apply 0001-Mini-Reference-Design-1-ZCU102-2016.2.patch


Apply the design-2 patch

$ git apply 0001-Mini-Reference-Design-2-ZCU102-2016.2.patch


Apply the design-3 patch

$ git apply 0001-Mini-Reference-Design-3-ZCU102-2016.2.patch



FSBL
FSBL build : refer DESIGN-1 at Tutorial 1

PMU Firmware
PMU FW build : refer DESIGN-1 at Tutorial 1

HEARTBEAT Application
Checkout HeartBeat Application sources from git
$ cd 2_rpu0_freertos_app/heartbeat

RPU0 HeartBeat build
follow common_procedure Build HeartBeat Application in the link: Common Functions


Perf APM Server Ctl Application
Checkout perfapm, perfapm-server, perfapm-server-ctl sources from git

$ cd 3_rpu1_baremetal_app

RPU1 perfapm-server-ctl (baremetal application without ipc )build:
RPU1 perfapm-server (baremetal application with ipc )build:
follow common_procedure PERFAPM-SERVER in the link: Common Functions


Device Tree
Use device tree same as DESIGN-1, refer DESIGN-1 at Tutorial 1

Kernel Image
Build the kernel image same as DESIGN-1, refer DESIGN-1 at Tutorial 1

Copy the RPU0's heartbeat.elf, RPU1's perfapm-server-ctl, PMUFW, FSBL images into petalinux build area
$ cp default_pmufw/Debug/default_pmufw.elf zynqmp_petalinux_bsp/images/linux/pmufw.elf
$ cp heartbeat/Debug/heartbeat.elf zynqmp_petalinux_bsp/images/linux
$ cp perfapm-server-ctl/Debug/perfapm-server-ctl.elf zynqmp_petalinux_bsp/images/linux
$ cp default_fsbl/Debug/default_fsbl.elf zynqmp_petalinux_bsp/images/linux/zynqmp_fsbl.elf


BOOT.BIN image
Create BOOT.BIN
$ cd images/linux
$ petalinux-package --force --boot --bif design3.bif
This will create zynqmp_petalinux_bsp/images/linux/BOOT.BIN

How to Execute

• Copy the below files onto SD card (root folder)

image.ub
boot.bin

• Insert the SD card into zcu102 board
• Connect power cable and UART cable
• Start TeraTerm or any other terminal application on Host PC (to view serial port messages)
• Power ON the board
• The board starts booting, observe for PMU FW messages followed by Linux boot messages

code

code