Zynq UltraScale+ MPSoC Base TRD 2019.2 - Design Module 1
Table of Contents
Design Overview
This design module showcases the following:
- Boot APU only
- FSBL, ATF, U-boot, PMU-FW
- APU OS: SMP Linux
- Ethernet via FTP/SCP
- Serial console via UART0
- File system via SD, USB or SATA
- Standard Linux applications on rootfs
Design Components
- petalinux_bsp
Build Flow Tutorials
Petalinux BSP
This tutorial shows how to build the Linux image and boot image using the PetaLinux build tool.Create and configure the PetaLinux project.
% cd $TRD_HOME/petalinux % petalinux-create -t project -s zcu102-prod-base-dm10.bsp -n bsp % cd bsp % petalinux-config --silentconfig
Select the device-tree matching design module 1 and build all Linux image components
% cd $TRD_HOME/petalinux/bsp/project-spec/meta-user/recipes-bsp/device-tree/files/ % rm system-user.dtsi % cp zcu102-base-dm1.dtsi system-user.dtsi % petalinux-build
Create a boot image.
% cd $TRD_HOME/petalinux/bsp/images/linux % petalinux-package --boot --bif=../../project-spec/boot/dm1.bif --force
Copy the generated boot image and Linux image to the dm1 SD card directory.
% mkdir -p $TRD_HOME/sd_card/dm1 % cp BOOT.BIN image.ub $TRD_HOME/sd_card/dm1
Run Flow Tutorial
- See here for board setup instructions.
- Copy all the files from the
$TRD_HOME/sd_card/dm1
SD card directory to a FAT formatted SD card. - Power on the board to boot the images; make sure all power rail LEDs are lit green (Note: DS1 / FPGA_INIT_B LED remains Red as there is no bit stream to configure the FPGA).
The user can now see Linux boot on the serial console:
Starting internet superserver: inetd. Configuring packages on first boot.... (This may take several minutes. Please do not power off the machine.) Running postinst /etc/rpm-postinsts/100-xserver-nodm-init... Running postinst /etc/rpm-postinsts/101-sysvinit-inittab... update-rc.d: /etc/init.d/run-postinsts exists during rc.d purge (continuing) INIT: Entering runlevel: 5 Configuring network interfaces... udhcpc (v1.24.1) started Sending select for 172.19.0.177... Lease of 172.19.0.177 obtained, lease time 1800 /etc/udhcpc.d/50default: Adding DNS 172.19.128.1 /etc/udhcpc.d/50default: Adding DNS 172.19.129.1 /etc/udhcpc.d/50default: Adding DNS 172.19.128.3 done. Starting system message bus: dbus. Starting Dropbear SSH server: dropbear. Starting bluetooth: bluetoothd. Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [ ok ] Starting Telephony daemon Starting tcf-agent: OK Setting console loglevel to 0 ... root@xilinx:~#
References
- How to mount a USB3.0 or SATA hard drive:
http://www.wiki.xilinx.com/SATA
http://www.wiki.xilinx.com/Zynq+Ultrascale+MPSOC+Linux+USB+device+driver (under host mode)
Next Steps
- Continue with Design Module 2.
- Return to the Design Tutorials Overview.
© Copyright 2019 - 2022 Xilinx Inc. Privacy Policy