Zynq UltraScale+ MPSoC Base TRD 2019.1 - Design Module 1

Table of Contents

---

Design Overview

This design module showcases the following:

• Boot APU only
  • FSBL, ATF, U-boot, PMU-FW
  • APU OS: SMP Linux
• Ethernet via FTP/SCP
• Serial console via UART0
• File system via SD, USB or SATA
• Standard Linux applications on rootfs

---

Design Components

• petalinux_bsp

---

Build Flow Tutorials

Petalinux BSP

This tutorial shows how to build the Linux image and boot image using the PetaLinux build tool.

• Create and configure the PetaLinux project.

  % cd $TRD_HOME/petalinux
  % petalinux-create -t project -s zcu102-prod-base-dm10.bsp -n bsp
  % cd bsp
  % petalinux-config --silentconfig

• Select the device-tree matching design module 1 and build all Linux image components

  % cd $TRD_HOME/petalinux/bsp/project-spec/meta-user/recipes-bsp/device-tree/files/
  % rm system-user.dtsi
  % cp zcu102-base-dm1.dtsi system-user.dtsi
  % petalinux-build

• Create a boot image.

  % cd $TRD_HOME/petalinux/bsp/images/linux
  % petalinux-package --boot --bif=../../project-spec/boot/dm1.bif --force

• Copy the generated boot image and Linux image to the dm1 SD card directory.

  % mkdir -p $TRD_HOME/sd_card/dm1
  % cp BOOT.BIN image.ub $TRD_HOME/sd_card/dm1

---

Run Flow Tutorial

• See here for board setup instructions.     
• Copy all the files from the $TRD_HOME/sd_card/dm1 SD card directory to a FAT formatted SD card.
• Power on the board to boot the images; make sure all power rail LEDs are lit green (Note: DS1 / FPGA_INIT_B LED remains Red as there is no bit stream to configure the FPGA).

• The user can now see Linux boot on the serial console:

  Starting internet superserver: inetd.
  Configuring packages on first boot....
   (This may take several minutes. Please do not power off the machine.)
  Running postinst /etc/rpm-postinsts/100-xserver-nodm-init...
  Running postinst /etc/rpm-postinsts/101-sysvinit-inittab...
  update-rc.d: /etc/init.d/run-postinsts exists during rc.d purge (continuing)
  INIT: Entering runlevel: 5
  Configuring network interfaces... 
  udhcpc (v1.24.1) started
  Sending select for 172.19.0.177...
  Lease of 172.19.0.177 obtained, lease time 1800
  /etc/udhcpc.d/50default: Adding DNS 172.19.128.1
  /etc/udhcpc.d/50default: Adding DNS 172.19.129.1
  /etc/udhcpc.d/50default: Adding DNS 172.19.128.3
  done.
  Starting system message bus: dbus.
  Starting Dropbear SSH server: dropbear.
  Starting bluetooth: bluetoothd.
  Starting syslogd/klogd: done
   * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon                       [ ok ]
  Starting Telephony daemon
  Starting tcf-agent: OK
  Setting console loglevel to 0 ...
  root@xilinx:~#

---

References

• How to mount a USB3.0 or SATA hard drive:
  http://www.wiki.xilinx.com/SATA
  http://www.wiki.xilinx.com/Zynq+Ultrascale+MPSOC+Linux+USB+device+driver (under host mode)

---