What is FSBL?
First Stage Bootloader (FSBL) for Zynq UltraScale+ MPSoC configures the FPGA with hardware bitstream (if it exists) and loads the Operating System (OS) Image or Standalone (SA) Image or 2nd Stage Boot Loader image from the non-volatile memory (NAND/SD/eMMC/QSPI) to Memory (DDR/TCM/OCM) and takes A53/R5 out of reset. It supports multiple partitions, and each partition can be a code image or a bitstream. Each of these partitions, if required, will be authenticated and/or decrypted.
FSBL is loaded into OCM and handed off by CSU BootROM after authenticating and/or decrypting (as required) FSBL.
How to create FSBL from Vitis?
- Launch VITIS with the below command: vitis
- Provide path where VITIS workspace and project need to be created. With this VITIS workspace will be created
- (Optional step) To work with local repos, Select "Xilinx" (ALT - x) -> Repositories. Against Local Repositories, click on "New..." and provide path of the local repo
- Select File-->New-->Application Project to open "New Project" window, provide name for FSBL project
- In the “Platform” section, click on “Create a new platform from hardware (XSA)” and select pre-defined hardware platform for ZynqMP (e.g. zcu102).
- Alternatively, to create a new/custom platform from a .xsa file, click on “+”, browse and select the XSA file and a new hardware platform is created.
- In the "Domain" window, select the processor psu_cortexa53_0/psu_cortexr5_0, OS as standalone and Language as C
- Click Next and select "Zynq MP FSBL"
- Click "Finish" to generate the A53/R5 FSBL. This populates the FSBL code and also builds it (along with BSP)
- Debug prints in FSBL are now disabled by default (except for FSBL banner). To enable debug prints, define symbol: FSBL_DEBUG_INFO
- In VITIS this can be done by: right click on FSBL application project -> select “C/C++ Build Settings” -> “Tool Settings” tab -> Symbols (under ARM v8 gcc compiler)
- Click on Add (+) icon and Enter Value: FSBL_DEBUG_INFO, click on "OK" to close the "Enter Value" screen
- In case any of the source files (FSBL or BSP) need to be modified, browse the file, make the change and save the file, build the project. elf file will be present in the Debug/Release folder of FSBL project.
What are various levels of debug prints in FSBL?FSBL supports four levels of debug prints:
|Type or prints||Purpose||Enabled by defining.. in FSBL code||Alternative way of enabling by defining symbol..|
|ALWAYS||Used for prints, which should be always enabled (e.g. FSBL banner)||FSBL_PRINT_VAL to (1U)||FSBL_PRINT|
|DEBUG GENERAL||To print errors and basic general information||FSBL_DEBUG_VAL to (1U)||FSBL_DEBUG|
|DEBUG INFO||To have more prints with format specifiers, in addition to basic general information||FSBL_DEBUG_INFO_VAL to (1U)||FSBL_DEBUG_INFO|
|DEBUG DETAILED||To have more detailed prints, in addition to above prints||FSBL_DEBUG_DETAILED_VAL to (1U)||FSBL_DEBUG_DETAILED|
On what all processor cores can FSBL run on?FSBL can only be run from A53_0 (AArch32 and AArch64), R5_0, R5_Lockstep
What part of OCM is used by FSBL?OCM region used by FSBL: 0xFFFC0000 – 0xFFFE9FFF. The last 512 bytes of this region is used by FSBL to share the handoff parameters corresponding to applications ATF hands off. FSBL fully uses this OCM region and, in fact, in certain designs and when certain features need to enabled, the current footprint of FSBL doesn't fit in this available OCM. For details, search for "footprint" in this wiki.
ATF uses the rest of OCM i.e. from 0xFFFEA000 to 0xFFFFFFFF. Please note that the current implementation of APU-only restart assumes that FSBL "resides" in OCM even after its execution is complete. This is since, in such scenarios, PMUFW hands off to (already existing) FSBL without actually restarting.
Hence, OCM is completely used between FSBL and ATF and with the available APU-only restart mechanism, no other application can reuse it.
How is xfsbl_translation_table.S different from translation_table.S of BSP?xfsbl_translation_table.S is a copy of file translation_table.S (of A53). The difference is that the FSBL’s copy of this file marks DDR region as reserved. This is to avoid speculative access to DDR before it is initialized. Once the DDR initialization is done in FSBL, memory attributes for DDR region is changed to “Memory” so that it is cacheable.
What ECC initialization is done by FSBL?TCM ECC Initialization: When FSBL runs on R5, TCM ECC is always initialized. Also, when FSBL loads application targeted on R5, the corresponding TCM's ECC is initialized. When FSBL runs on A53, by default, TCM ECC is not initialized as this also involves powering up of RPU. In such cases, TCM ECC Initialization can be performed by defining FSBL_A53_TCM_ECC_EXCLUDE_VAL to 0 in xfsbl_config.h.
DDR ECC Initialization: Done in FSBL if ECC for DDR is enabled in design.
I’m unable to build FSBL due to size issues, how can I reduce its footprint?FSBL provides option to enable/disable certain features from building. By selectively disabling certain features as mentioned in below table, code size can be reduced. These flags are defined in xfsbl_config.h of FSBL.
|FLAG||default value||Meaning of default setting / Notes||Significant impact on FSBL size?|
|FSBL_NAND_EXCLUDE_VAL||(0U)||NAND Boot mode related code is included (if NAND is present in design)||Yes|
|FSBL_QSPI_EXCLUDE_VAL||(0U)||QSPI Boot mode related code is included (if QSPI is present in design)||Yes|
|FSBL_SD_EXCLUDE_VAL||(0U)||SD Boot mode related code is included (if SD is present in design)||Yes|
|FSBL_SECURE_EXCLUDE_VAL||(0U)||Secure features (Authenctication and decryption) are enabled||Yes|
|FSBL_BS_EXCLUDE_VAL||(0U)||PL Bitstream load capability is enabled||Yes|
|FSBL_SHA2_EXCLUDE_VAL||(1U)||SHA2 is not supported||Yes|
|FSBL_EARLY_HANDOFF_EXCLUDE_VAL||(1U)||This flag/feature is not fully supported and hence is not recommended to change this setting||No|
|FSBL_WDT_EXCLUDE_VAL||(0U)||Watchdod timer feature is included||No|
|FSBL_PERF_EXCLUDE_VAL||(1U)||Performance prints are not shown by default||No|
|FSBL_A53_TCM_ECC_EXCLUDE_VAL||(1U)||TCM ECC is not initialized for A53 ALWAYS. Changing this flag will result in TCM ECC being initialized always.||No|
|FSBL_PL_CLEAR_EXCLUDE_VAL||(1U)||PL Initialization/clearing will be done ONLY when the boot image has PL bitstream. Changing this will result in PL Initialization/clearing to be done ALWAYS during FSBL Initialization||No|
|FSBL_USB_EXCLUDE_VAL||(1U)||USB Slave boot mode support is disabled||Yes|
|FSBL_PROT_BYPASS_EXCLUDE_VAL||(1U)||By default (from 2018.1), complete XMPU/XPPU configuration is done. Changing this flag will result in FSBL bypassing XPPU and FPD XMPU configuration and isolation/protection feature will be just limited to OCM slave.||No|
|FSBL_PARTITION_LOAD_EXCLUDE_VAL||(0U)||By default FSBL loads all the partitions in the image, if this macro is been set, FSBL skips the partitions loading and will run the way it runs in JTAG boot mode.|
|FSBL_FORCE_ENC_EXCLUDE_VAL||(0U)||By default FSBL forces encryption of all the partitions when ENC_ONLY bit is blown, but if this macro is been set encryption can be optional for all the partitions loaded by FSBL, however it is compulsory for FSBL partition.|
Are there any other ways by which FSBL footprint can be further reduced?Debug prints: By default only FSBL banner is printed. If more debug prints are enabled, these will result in use of more memory.
Drivers Asserts: Asserts are used within all Xilinx drivers and can be turned off on a system-wide basis by defining, at compile time, the NDEBUG identifier (adding –DNDEBUG against extra_compiler_flags of drivers). This will help further reduce FSBL footprint.
I’m unable to debug FSBL in Vitis. Any change in optimizations used by FSBL?
For 2019.2, FSBL will be built with –Os and LTO optimizations by default in VITIS.If the user need to disable the optimization (for debugging), two things need to be done:
Since removing optimization
In order to debug, the following are two options :
- Remove Optimizations
- Check "xfsbl_config.h" file, make sure that EXCLUDE flags options are not enabled/included. One thing to note here is that removing optimizations results in increase of code size and can result in not being able to build FSBL
- Disable some of the features that he does not require in xfsbl_config.h file of FSBL .
To disable Optimizations, below changes need to be done:
FSBL app: In the “Miscellaneous” section, need to remove highlighted options below:
- . In this case, the second option (of reducing optimization) can be looked at and followed.
- Reduce/Change the level of Optimization
- The first step can be done in three ways
- Disable Optimizations - In the "Miscellaneous" Section of FSBL app, remove highlighted options below. In some cases, this would still make the FSBL too big to not be able to fit in OCM and proceed with debug.
- Modify flags to remove "-Os -flto -ffat
- The first step can be done in three ways
- -lto-objects" and include only -O1 instead.
- If doing the above doesn't work and -O1 is still difficult to debug, modify flags to remove "-Os -flto -ffat-lto-objects" and include -Og instead.
-Og stands for Optimized Debug Experience. To be used along with this, some of the optimization flags can be tried manually.
"-Og -finline-functions-called-once" is known to have worked.
Refer to the following doc for more info : https://gcc.gnu.org/onlinedocs/gcc-8.2.0/gcc/Optimize-Options.html#Optimize-Options
b. The following needs to be done after reducing opt by following either of the three methods above.
BSP settings: highlighted Highlighted zynqmp_fsbl_bsp flag need to be changed to false (to avoid turning on of optimization again of BSP for FSBL during rebuilding caused by above change.