root@xilinx-vck190-2021_2:~# ./apu_script.sh
APU: Versal interface
APU: Setting all APU frequency to 1199999

[  131.521469] fpga_manager fpga0: writing partial.pdi to Xilinx Versal FPGA Manager
[147193.924]Loading PDI from DDR
[147194.040]Monolithic/Master Device
[147197.345]3.392 ms: PDI initialization time
[147201.323]+++Loading Image#: 0x0, Name: pl_cfi_unmask, Id: 0x18700002
[147207.575]---Loading Partition#: 0x0, Id: 0x103
[147267.610] 55.636 ms for Partition#: 0x0, Size: 35104 Bytes
[147270.212]---Loading Partition#: 0x1, Id: 0x105
[147274.860] 0.255 ms for Partition#: 0x1, Size: 4656 Bytes
[147279.805]---Loading Partition#: 0x2, Id: 0x205
[147287.166] 2.966 ms for Partition#: 0x2, Size: 54352 Bytes
[147289.682]---Loading Partition#: 0x3, Id: 0x203
[147294.106] 0.028 ms for Partition#: 0x3, Size: 544 Bytes
[147299.192]---Loading Partition#: 0x4, Id: 0x303
[147345.369] 41.780 ms for Partition#: 0x4, Size: 5428464 Bytes
[147348.141]---Loading Partition#: 0x5, Id: 0x305
[147353.581] 1.045 ms for Partition#: 0x5, Size: 28112 Bytes
[147357.819]---Loading Partition#: 0x6, Id: 0x403
[147362.420] 0.207 ms for Partition#: 0x6, Size: 243648 Bytes
[147367.584]---Loading Partition#: 0x7, Id: 0x405
[147372.243] 0.264 ms for Partition#: 0x7, Size: 4704 Bytes
[147377.237]Subsystem PDI Load: Done
[  131.725508] OF: overlay: WARNING: memory leak will occur if overlay removed, property: /fpga/firmware-name
[  131.736753] OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/overlay0
[  131.746586] OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/fpga_PR0
[  131.756755] of-fpga-region fpga:fpga-PR0: FPGA Region probed
APU: *********************** APU, RPU and PL in full power mode **********************
APU: Delay 60 seconds

APU: Powering off PL domain

real    0m0.033s
user    0m0.006s
sys     0m0.000s
[  191.890911] fpga_manager fpga0: writing greybox.pdi to Xilinx Versal FPGA Manager
[206826.345]Loading PDI from DDR
[206826.461]Monolithic/Master Device
[206829.767]3.394 ms: PDI initialization time
[206833.749]+++Loading Image#: 0x0, Name: pl_cfi_unmask, Id: 0x18700002
[206840.006]---Loading Partition#: 0x0, Id: 0x103
[206844.612] 0.209 ms for Partition#: 0x0, Size: 35104 Bytes
[206849.693]---Loading Partition#: 0x1, Id: 0x105
[206854.346] 0.255 ms for Partition#: 0x1, Size: 4656 Bytes
[206859.297]---Loading Partition#: 0x2, Id: 0x205
[206866.662] 2.965 ms for Partition#: 0x2, Size: 54352 Bytes
[206869.179]---Loading Partition#: 0x3, Id: 0x203
[206873.605] 0.028 ms for Partition#: 0x3, Size: 544 Bytes
[206878.694]---Loading Partition#: 0x4, Id: 0x303
[206924.914] 41.822 ms for Partition#: 0x4, Size: 5428464 Bytes
[206927.689]---Loading Partition#: 0x5, Id: 0x305
[206933.129] 1.044 ms for Partition#: 0x5, Size: 28112 Bytes
[206937.373]---Loading Partition#: 0x6, Id: 0x403
[206941.978] 0.207 ms for Partition#: 0x6, Size: 243648 Bytes
[206947.147]---Loading Partition#: 0x7, Id: 0x405
[206952.473] 0.930 ms for Partition#: 0x7, Size: 4672 Bytes
[206956.805]Subsystem PDI Load: Done
[  192.190255] OF: overlay: WARNING: memory leak will occur if overlay removed, property: /fpga/firmware-name
[  192.199938] OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/overlay0
[  192.209770] OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/fpga_PR0
[  192.219933] of-fpga-region fpga:fpga-PR0: FPGA Region probed

real    0m0.481s
user    0m0.015s
sys     0m0.198s
APU: ********************* APU and RPU full load, PL is OFF **************************
APU: Delay 60 seconds

APU: Sending sync command to idle RPU
RPU: DelayVal = 60
RPU: (60 seconds RTC timer)
APU: ********************* APU full load, RPU idle, PL is OFF ************************
APU: Delay 60 seconds

RPU: RTC Alarm generated.
RPU: (1 seconds delay)
APU: Sending sync command

APU: Latency to Power OFF APU1 core
[  312.461144] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1349998650 (-34)
[  312.493201] CPU1: shutdown
[  312.495933] psci: CPU1 killed (polled 0 ms)

real    0m0.095s
user    0m0.000s
sys     0m0.007s
APU: Delay 60 seconds

RPU: (60 seconds RTC timer)
RPU: RTC Alarm generated.
RPU: (1 seconds delay)
APU: Sending sync command
APU: ************ APU (APU0 only) full load, RPU idle, PL is OFF *********************
APU: Delay 60 seconds

RPU: (60 seconds RTC timer)
RPU: RTC Alarm generated.
RPU: (1 seconds delay)
APU: Sending sync command
APU: Setting APU0 frequency to 29[  433.861557] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1349998650 (-34)
9999

real    0m0.028s
user    0m0.000s
sys     0m0.012s
APU: ********** APU (APU0 low freq) full load, RPU idle, PL is OFF *******************
APU: Delay 60 seconds

RPU: (60 seconds RTC timer)


RPU: RTC Alarm generated.
RPU: (1 seconds delay)
APU: Sending sync command

real    0m0.041s
user    0m0.004s
sys     0m0.010s
APU: Setting APU0 frequency to 1199999
APU: *********************** APU Linux Idle, RPU idle, PL is OFF *********************
APU: Delay 60 seconds

RPU: (60 seconds RTC timer)
RPU: RTC Alarm generated.
RPU: (1 seconds delay)
APU: Sending sync command
RPU: IterationCnt = 1
RPU: Latency Measurement Start. Total iteration is 1
RPU: Latency measurement iteration count : 1
RPU: ******************************** RPU ON, APU ON *********************************
APU: APU Suspend requenst came[  557.147902] PM: suspend entry (deep)
 from RPU
[  557.153241] Filesystems sync: 0.000 seconds
[  557.160230] (NULL device *): Direct firmware load for partial.pdi failed with error -2
[  557.168306] (NULL device *): Direct firmware load for greybox.pdi failed with error -2
[  557.176358] Freezing user space processes ... (elapsed 0.000 seconds) done.
[  557.184101] OOM killer disabled.
[  557.187321] Freezing remaining freezable tasks ... (elapsed 0.039 seconds) done.
[  557.245931] macb ff0c0000.ethernet eth0: Link is Down
[  557.253899] Disabling non-boot CPUs ...
RPU: *********************** RPU ON, APU suspended with FPD ON ***********************
RPU: (3 seconds delay)
RPU: FPD will be off after releasing 0x18224029
RPU: XPm_ReleaseNode(18224029, 0, 0, 0, 0)
RPU: XPm_NotifyCb (69255171, 1, 0)
RPU: *********************** RPU ON, APU suspended with FPD OFF **********************
RPU: (3 seconds delay)
RPU: XPm_RequestWakeUp(1810C003, 0, 0, 0, 0)
[575334.857]Loading from BootPdi
[575337.774]FlashID=0x20 0xBB 0x21
[575340.840]+++Loading Image#: 0x3, Name: fpd, Id: 0x0420C003
[575346.236]---Loading Partition#: 0x8, Id: 0x0
RPU: XPm_NotifyCb (69255171, 1, 2[
75354.906] 4.445 ms for Partition#: 0x8, Size: 1104 Bytes
RPU: XPm_NotifyCb (69255171, 1, 2)
RPU: XPm_RequestNode(18224029, 1, 0, 0, 0)
[  557.259936] spi-nor spi0.0: trying to lock already unlocked area
[  557.266030] macb ff0c0000.ethernet eth0: configuring for phy/rgmii-id link mode
[  557.273894] macb ff0c0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[  557.283400] macb ff0c0000.ethernet eth0: Link is Down
[  557.469183] usb 1-1: reset high-speed USB device number 2 using xhci-hcd
[  557.621407] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1349998650 (-34)
[  557.630760] OOM killer enabled.
[  557.633902] Restarting tasks ... done.
[  557.640536] PM: suspend exit
APU: Sending sync command
RPU: ******************************** RPU ON, APU ON *********************************
RPU: (3 seconds delay)
[  557.675014] mmc0: card aaaa removed
[  558.695814] mmc0: new SDHC card at address aaaa
[  558.702669] mmcblk0: mmc0:aaaa SC16G 14.8 GiB
[  558.714968]  mmcblk0: p1 p2
[  559.238898] EXT4-fs (mmcblk0p2): recovery complete
[  559.243733] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[  559.260556] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  560.337971] macb ff0c0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
RPU: Request Suspend Latency of Linux in micro seconds: Min: 113808, Max: 113808, Avg: 113808
RPU: FPD OFF Latency in micro seconds: Min: 6857, Max: 6857, Avg: 6857
RPU: Wakeup Latency of APU0 in micro seconds: Min: 29750, Max: 29750, Avg: 29750
RPU: Wakeup Latency of Linux in micro seconds: Min: 493969, Max: 493969, Avg: 493969
RPU: Latency Measurement Done
APU: APU Suspend requenst[  561.586972] PM: suspend entry (deep)
 came from RPU
[  561.592301] Filesystems sync: 0.000 seconds
[  561.598234] (NULL device *): Direct firmware load for partial.pdi failed with error -2
[  561.606184] (NULL device *): Direct firmware load for greybox.pdi failed with error -2
[  561.614181] Freezing user space processes ... (elapsed 0.001 seconds) done.
[  561.622245] OOM killer disabled.
[  561.625465] Freezing remaining freezable tasks ... (elapsed 0.071 seconds) done.
[  561.713862] macb ff0c0000.ethernet eth0: Link is Down
[  561.721824] Disabling non-boot CPUs ...
RPU: (3 seconds delay)
RPU: ********************** RPU Idle, APU suspended with FPD ON **********************
RPU: (60 seconds RTC timer)
RPU: RTC Alarm generated.
RPU: XPm_ReleaseNode(18224029, 0, 0, 0, 0)
RPU: XPm_NotifyCb (69255171, 1, 0)
RPU: *********************** RPU ON, APU suspended with FPD OFF **********************
RPU: (60 seconds delay)
RPU: (60 seconds RTC timer)
RPU: ********************** RPU Idle, APU suspended with FPD OFF *********************
RPU: RTC Alarm generated.
RPU: (60 seconds RTC timer)
RPU: XPm_SetWakeUpSource(18110005, 18224034, 1, 0, 0)
RPU: XPm_SelfSuspend(18110005, FFFF, F, FFE00000, 0)
RPU: ******************* RPU Suspended, APU suspended with FPD OFF *******************
RPU: Going to WFI...
RPU: Running in lock-step mode
RPU: RESUMED
RPU: RTC Alarm generated.
RPU: *********************** RPU ON, APU suspended with FPD OFF **********************
RPU: (60 seconds delay)
RPU: ********************** RPU Idle, APU suspended with FPD OFF *********************
RPU: (60 seconds RTC timer)
RPU: RTC Alarm generated.
RPU: XPm_RequestWakeUp(1810C003, 0, 0, 0, 0)
[973780.565]Loading from BootPdi
[973783.485]FlashID=0x20 0xBB 0x21
[973786.553]+++Loading Image#: 0x3, Name: fpd, Id: 0x0420C003
[973791.955]---Loading Partition#: 0x8, Id: 0x0
RPU: XPm_NotifyCb (69255171, 1, 2)
73800.631] 4.449 ms for Partition#: 0x8, Size: 1104 Bytes
RPU: XPm_NotifyCb (69255171,  , 2).727858] spi-nor spi0.0: trying to lock already unlocked area
[  561.736808] macb ff0c0000.ethernet eth0: configuring for phy/rgmii-id link mode
[  561.744672] macb ff0c0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
[  561.754009] macb ff0c0000.ethernet eth0: Link is Down
[  561.937175] usb 1-1: reset high-speed USB device number 2 using xhci-hcd
[  562.089401] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1349998650 (-34)
[  562.098751] OOM killer enabled.
[  562.101894] Restarting tasks ... done.
[  562.106550] PM: suspend exit
APU: Resumed script successfully
APU: Sending syRPU: ******************************** RPU ON, APU ON *********************************
RPU: (60 seconds RTC timer)
nc command
APU: *********************** APU Linux Idle, RPU Idle, PL is OFF ****************
APU: Delay 60 seconds

[  562.141331] mmc0: card aaaa removed
[  563.161937] mmc0: new SDHC card at address aaaa
[  563.167159] mmcblk0: mmc0:aaaa SC16G 14.8 GiB
[  563.176779]  mmcblk0: p1 p2
[  563.698361] EXT4-fs (mmcblk0p2): recovery complete
[  563.703164] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[  563.718538] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[  564.817873] macb ff0c0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off
RPU: RTC Alarm generated.
RPU: (1 seconds delay)
APU: Sending sync command
APU: Setting APU0 frequency to 29[  622.126441] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1349998650 (-34)
9999

real    0m0.031s
user    0m0.003s
sys     0m0.009s
APU: ********** APU (APU0 low freq) full load, RPU idle, PL is OFF *******************
APU: Delay 60 seconds

RPU: (60 seconds RTC timer)
RPU: RTC Alarm generated.
RPU: (1 seconds delay)
APU: Sending sync command
APU: Setting APU0 frequency to 1199999

real    0m0.000s
user    0m0.000s
sys     0m0.000s
APU: ************ APU (APU0 only) full load, RPU idle, PL is OFF *********************
APU: Delay 60 seconds

RPU: (60 seconds RTC timer)
RPU: RTC Alarm generated.
RPU: (1 seconds delay)
APU: Sending sync command

APU: Latency to Power ON APU1 core
[  743.763415] Detected PIPT I-cache on CPU1
[  743.767437] GICv3: CPU1: found redistributor 1 region 0:0x00000000f90a0000
[  743.774325] CPU1: Booted secondary processor 0x0000000001 [0x410fd083]
[  743.781125] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP for freq 1349998650 (-34)

real    0m0.056s
user    0m0.000s
sys     0m0.000s
APU: Delay 60 seconds

RPU: (60 seconds RTC timer)
RPU: RTC Alarm generated.
RPU: (1 seconds delay)
APU: Sending sync command
APU: ********************* APU full load, RPU idle, PL is OFF ************************
APU: Delay 60 seconds

RPU: (60 seconds RTC timer)
RPU: RTC Alarm generated.
RPU: (1 seconds delay)
APU: Sending sync command
APU: ********************* APU and RPU full load, PL is OFF **************************
APU: Delay 60 seconds

APU: Powering on PL domain

real    0m0.035s
user    0m0.006s
sys     0m0.000s
[  925.894899] fpga_manager fpga0: writing partial.pdi to Xilinx Versal FPGA Manager
[1333435.115]Loading PDI from DDR
[1333435.318]Monolithic/Master Device
[1333438.713]3.569 ms: PDI initialization time
[1333442.782]+++Loading Image#: 0x0, Name: pl_cfi_unmask, Id: 0x18700002
[1333449.129]---Loading Partition#: 0x0, Id: 0x103
[1333509.262] 55.644 ms for Partition#: 0x0, Size: 35104 Bytes
[1333511.953]---Loading Partition#: 0x1, Id: 0x105
[1333516.694] 0.255 ms for Partition#: 0x1, Size: 4656 Bytes
[1333521.732]---Loading Partition#: 0x2, Id: 0x205
[1333529.188] 2.970 ms for Partition#: 0x2, Size: 54352 Bytes
[1333531.793]---Loading Partition#: 0x3, Id: 0x203
[1333536.308] 0.028 ms for Partition#: 0x3, Size: 544 Bytes
[1333541.487]---Loading Partition#: 0x4, Id: 0x303
[1333587.821] 41.847 ms for Partition#: 0x4, Size: 5428464 Bytes
[1333590.686]---Loading Partition#: 0x5, Id: 0x305
[1333596.221] 1.045 ms for Partition#: 0x5, Size: 28112 Bytes
[1333600.552]---Loading Partition#: 0x6, Id: 0x403
[1333605.246] 0.208 ms for Partition#: 0x6, Size: 243648 Bytes
[1333610.503]---Loading Partition#: 0x7, Id: 0x405
[1333615.252] 0.264 ms for Partition#: 0x7, Size: 4704 Bytes
[1333620.340]Subsystem PDI Load: Done
[  926.302243] OF: overlay: WARNING: memory leak will occur if overlay removed, property: /fpga/firmware-name
[  926.311919] OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/overlay0
[  926.321751] OF: overlay: WARNING: memory leak will occur if overlay removed, property: /__symbols__/fpga_PR0
[  926.331916] of-fpga-region fpga:fpga-PR0: FPGA Region probed

real    0m0.596s
user    0m0.015s
sys     0m0.253s
APU: *********************** APU, RPU and PL in high power ***************************
APU: Delay 60 seconds

APU: Demo application is completed successfully!
root@xilinx-vck190-2021_2:~#
root@xilinx-vck190-2021_2:~#
root@xilinx-vck190-2021_2:~#