U-Boot 2013.01 (Apr 15 2013 - 09:22:53) I2C: ready DRAM: 1 GiB WARNING: Caches not enabled MMC: zynq_sdhci: 0 SF: Detected N25Q128A with page size 64 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: Gem.e000b000 Hit any key to stop autoboot: 3  2  1  0 Copying Linux from SD to RAM... Device: zynq_sdhci Manufacturer ID: 1b OEM: 534d Name: 00000 Tran Speed: 50000000 Rd Block Len: 512 SD version 2.0 High Capacity: Yes Capacity: 7.5 GiB Bus Width: 4-bit reading uImage 2996704 bytes read in 437 ms (6.5 MiB/s) reading devicetree.dtb 6378 bytes read in 13 ms (478.5 KiB/s) reading uramdisk.image.gz 3387520 bytes read in 482 ms (6.7 MiB/s) ## Booting kernel from Legacy Image at 03000000 ... Image Name: Linux-3.8.0-xilinx-00015-gabc285 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2996640 Bytes = 2.9 MiB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 3387456 Bytes = 3.2 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 02a00000 Booting using the fdt blob at 0x02a00000 Loading Kernel Image ... OK OK Loading Ramdisk to 1fcc4000, end 1ffff040 ... OK Loading Device Tree to 1fcbf000, end 1fcc38e9 ... OK Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 3.8.0-xilinx-00015-gabc285b (sorenb@xsjandreislx) (gcc version 4.6.1 (Sourcery CodeBench Lite 2011.09-50) ) #1 SMP PREEMPT Mon Apr 15 09:22:29 PDT 2013 CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Xilinx Zynq Platform, model: Xilinx Zynq ZC702 bootconsole [earlycon0] enabled cma: CMA: reserved 16 MiB at 2e800000 Memory policy: ECC disabled, Data cache writealloc PERCPU: Embedded 7 pages/cpu @c0db0000 s7616 r8192 d12864 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 260096 Kernel command line: console=ttyPS0,115200 root=/dev/mmcblk0p2 rw earlyprintk PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) __ex_table already sorted, skipping sort Memory: 1024MB = 1024MB total Memory: 1013936k/1013936k available, 34640k reserved, 270336K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) lowmem : 0xc0000000 - 0xef800000 ( 760 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc05171b4 (5181 kB) .init : 0xc0518000 - 0xc0540dc0 ( 164 kB) .data : 0xc0542000 - 0xc057ac30 ( 228 kB) .bss : 0xc057ac30 - 0xc05a5258 ( 170 kB) Preemptible hierarchical RCU implementation. Dump stacks of tasks blocking RCU-preempt GP. RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2. NR_IRQS:16 nr_irqs:16 16 MIO pin 47 not assigned(00001220) xslcr mapped to f0002000 Zynq clock init timer #0 at f0004000, irq=43 sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms Console: colour dummy device 80x30 Calibrating delay loop... 1332.01 BogoMIPS (lpj=6660096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x3af1e8 - 0x3af21c L310 cache controller enabled l2x0: 8 ways, CACHE_ID 0x000000c0, AUX_CTRL 0x72360000, Cache size: 524288 B CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 Brought up 2 CPUs SMP: Total of 2 processors activated (2664.03 BogoMIPS). devtmpfs: initialized NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations xgpiops e000a000.gpio: gpio at 0xe000a000 mapped to 0xf000c000 hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. bio: create slab at 0 vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered Switching to clocksource xttcps_clocksource NET: Registered protocol family 2 TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP: reno registered UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... Freeing initrd memory: 3308K hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available bounce pool size: 64 pages jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc. msgmni has been set to 1490 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-267056 dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16 xuartps e0001000.uart: failed to get alias id, errno -19 e00ðconsole [ttyPS0] enabled, bootconsole disabled console [ttyPS0] enabled, bootconsole disabled xdevcfg f8007000.devcfg: ioremap f8007000 to f0062000 with size 100 brd: module loaded loop: module loaded xqspips e000d000.spi: master is unqueued, this is deprecated m25p80 spi1.0: found n25q128, expected n25q128 m25p80 spi1.0: n25q128 (16384 Kbytes) 5 ofpart partitions found on MTD device spi1.0 Creating 5 MTD partitions on "spi1.0": 0x000000000000-0x000000100000 : "qspi-fsbl-uboot" 0x000000100000-0x000000600000 : "qspi-linux" 0x000000600000-0x000000620000 : "qspi-device-tree" 0x000000620000-0x000000c00000 : "qspi-rootfs" 0x000000c00000-0x000001000000 : "qspi-bitstream" xqspips e000d000.spi: at 0xE000D000 mapped to 0xF0064000, irq=51 e1000e: Intel(R) PRO/1000 Network Driver - 2.1.4-k e1000e: Copyright(c) 1999 - 2012 Intel Corporation. libphy: XEMACPS mii bus: probed xemacps e000b000.eth: pdev->id -1, baseaddr 0xe000b000, irq 54 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ULPI transceiver vendor/product ID 0x0424/0x0007 Found SMSC USB3320 ULPI transceiver. ULPI integrity check: passed. xusbps-ehci xusbps-ehci.0: Xilinx PS USB EHCI Host Controller xusbps-ehci xusbps-ehci.0: new USB bus registered, assigned bus number 1 xusbps-ehci xusbps-ehci.0: irq 53, io mem 0x00000000 xusbps-ehci xusbps-ehci.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mousedev: PS/2 mouse device common for all mice i2c /dev entries driver xi2cps e0004000.i2c: 100 kHz mmio e0004000 irq 57 i2c i2c-0: Added multiplexed i2c bus 1 si570 1-005d: registered si570 with default frequency 156250000 Hz si570 1-005d: set initial output frequency 148500000 Hz i2c i2c-0: Added multiplexed i2c bus 2 i2c i2c-0: Added multiplexed i2c bus 3 at24 3-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write i2c i2c-0: Added multiplexed i2c bus 4 i2c i2c-0: Added multiplexed i2c bus 5 rtc-pcf8563 5-0051: chip found, driver version 0.4.3 rtc-pcf8563 5-0051: low voltage detected, date/time is not reliable. rtc-pcf8563 5-0051: rtc core: registered rtc-pcf8563 as rtc0 i2c i2c-0: Added multiplexed i2c bus 6 i2c i2c-0: Added multiplexed i2c bus 7 i2c i2c-0: Added multiplexed i2c bus 8 pca954x 0-0074: registered 8 multiplexed busses for I2C switch pca9548 xadcps f8007100.xadc: enabled: yes reference: external mpcore_wdt: MPcore Watchdog Timer: 0.1. mpcore_noboot=0 mpcore_margin=60 sec (nowayout= 0) xwdtps f8005000.swdt: Xilinx Watchdog Timer at f006e000 with timeout 10s sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci-pltfm: SDHCI platform and OF driver helper mmc0: Invalid maximum block size, assuming 512 bytes mmc0: SDHCI controller on e0100000.sdhci [e0100000.sdhci] using ADMA usbcore: registered new interface driver usbhid usbhid: USB HID core driver TCP: cubic registered NET: Registered protocol family 17 VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 Registering SWP/SWPB emulation handler dmatest: Started 1 threads using dma0chan0 dmatest: Started 1 threads using dma0chan1 dmatest: Started 1 threads using dma0chan2 dmatest: Started 1 threads using dma0chan3 dmatest: Started 1 threads using dma0chan4 dmatest: Started 1 threads using dma0chan5 mmc0: new high speed SDHC card at address b368 dmatest: Started 1 threads using dma0chan6 mmcblk0: mmc0:b368 00000 7.51 GiB mmcblk0: p1 p2 dmatest: Started 1 threads using dma0chan7 rtc-pcf8563 5-0051: low voltage detected, date/time is not reliable. rtc-pcf8563 5-0051: setting system clock to 2013-04-15 16:52:12 UTC (1366044732) Freeing init memory: 160K do mounts start mdev mdev: /sys/class: No such file or directory mount root EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240) EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240) EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) hand off to new root * Starting NTP server ntpd  [ OK ] Ubuntu 12.10 zynq ttyPS0 zynq login: root Password: Last login: Mon Apr 15 09:49:21 PDT 2013 on ttyPS0 Welcome to Ubuntu 12.10 (GNU/Linux 3.8.0-xilinx-00015-gabc285b armv7l) * Documentation: https://help.ubuntu.com/ root@zynq:~#